A progressive approach to predict shot peening process parameters for forming integral panel of Al7050-T7451

In this paper, a progressive approach to predict the multiple shot peening process parameters for complex integral panel is proposed. Firstly, the invariable parameters in the forming process including shot size, mass flow, peening distance and peening angle are determined according to the empirical and machine type. Then, the optimal value of air pressure for the whole shot peening is selected by the experimental data. Finally, the feeding speed for every shot peening path is predicted by regression equation. The integral panel part with thickness from 2 mm to 5 mm and curvature radius from 3200 mm to 16000 mm is taken as a research object, and four experiments are conducted. In order to design specimens for acquiring the forming data, one experiment is conducted to compare the curvature radius of the plate and stringer-structural specimens, which were peened along the middle of the two stringers. The most striking finding of this experiment is that the outer shape error range is below 3.9%, so the plate specimens can be used in predicting feeding speed of the integral panel. The second experiment is performed and results show that when the coverage reaches the limit of 80%, the minimum feeding speed is 50 mm/s. By this feeding speed, the forming curvature radius of the specimens with different thickness from the third experiment is measured and compared with the research object, and the optimal air pressure is 0.15 MPa. Then, the plate specimens with thickness from 2 mm to 5 mm are peened in the fourth experiment, and the measured curvature radius data are used to calculate the feeding speed of different shot peening path by regressive analysis method. The algorithm is validated by forming a test part and the average deviation is 0.496 mm. It is shown that the approach can realize the forming of the integral panel precisely.     

Implementation of tactical maneuvers with maneuver libraries

This study creates and combines the general maneuver libraries for fixed-wing aircraft to implement tactical maneuvers. First, the generalized maneuver libraries are established by analyzing the characteristics of tactical maneuvers required in battlefields. The 7th order polynomial is applied to both the creation of the maneuver libraries and the generation of the trajectories or flight paths for modal inputs. To track the desired trajectory, we design the Attitude Command Attitude Hold (ACAH) system and the Rate Command Rate Hold (RCRH) system using Model Following Controller (MFC). Moreover, the Line-of-Sight (LOS) guidance law is designed. In particular, the CONDUIT® is employed to optimize the gains so that the control systems meet the aircraft Handling Qualities (HQ) criteria. Finally, flight simulations are performed for the longitudinal loop, immelmann-turn, and climb-slalom-descent maneuvers to verify that tactical aggressive maneuvers are realizable via the combination of maneuver libraries. This study can contribute to the development of flight techniques for aircraft tactical maneuvers and to the revision of air force operational manuals.     

偏心撞击对撞击式喷嘴雾化特性的影响

为研究偏心撞击对撞击式喷嘴雾化特性的影响,建立了求解自燃推进剂冷态射流撞击雾化过程的数值模拟方案,计算了不同偏心度条件下的射流撞击雾化过程。采用树形自适应加密算法直接求解不可压Navier-Stokes方程组,由分段线性的流体体积(VOF)方法对流体界面进行捕捉。结果表明偏心撞击会导致雾场发生偏转,当无量纲偏心度E为1/8时,雾场偏转角度约为9.2°,应控制加工偏差小于该值。随着偏心度的增大,液膜的偏转角度增大,理论推导得到的液膜偏转角度要小于数值计算得到的液膜偏转角度。正心撞击时燃料与氧化剂流强峰值接近,雾场的流强分布呈单峰分布。当发生偏心撞击时,由于燃料与氧化剂部分射流未参与撞击导致流强峰值出现交错,雾场的流强分布呈双峰分布,混合比的空间分布发生较大改变。正心撞击时撞击点下游液滴的速度分布近似呈轴对称分布,而偏心撞击之后的速度分布则呈中心对称分布。偏心撞击导致的射流动量损失使得雾化性能变差,当无量纲偏心度E为1/8时,一甲基肼(MMH)的Sauter平均直径增大约4.8%,四氧化二氮(NTO)的Sauter平均直径增大约5.8%。      

Review and propositions for the sliding/impact wear behavior in a contact interface

A thermal-solid-liquid complex operational environment induces structural interface developing a typical coupling sliding/impact wear behavior. It results in contact damage until systems fail, which may cause significant economic losses and catastrophic consequences. The key point of solving this problem is to reveal the coupling damage mechanism of the sliding/impact behavior in typical systems and life characterization under a complicate evolving environment. This has been a hot topic in the area of mechanical reliability. The main work in this paper can be concluded as follows. Firstly, the main industries in which the “sliding/impact behavior” takes place have been introduced. Then, existing studies on the wear mechanism and degree analysis are presented, which includes surface morphology analysis, wear debris analysis, and wear degree measurement. Meanwhile, existing problems in theoretical modeling and experiments in current research are summarized, so as to point out a bright direction for future research on wear prediction. They include interface contact modeling, mathematic coupling mechanism modeling, wear equation establishment, and wear life characterization, which can provide some new ideas for improving the existing studies on the sliding/impact wear behavior.     

推进我国企业债券利率市场化的措施

企业债券利率市场化是我国利率市场化改革的重要组成部分。目前,我国已经基本具备了企业债券利率市场化的条件,宏观经济环境稳定,微观经济主体日趋理性,国债和金融债券发行利率市场化也为下一步实现企业债券发行利率市场化提供了宝贵的经验。鉴于此,可以根据企业债券融资发展的不同阶段,采取相应措施加快我国企业债券利率市场化的步伐,主要包括:取消发债企业的所有制限制、培育企业债券流通市场、逐步取消发债规模限制、放宽发行利率的浮动幅度、健全企业债券风险监管制度、规范企业债券信用评级。     

用亚稳态正电子素研究络合的瞬态反应（Ⅲ）

本文用自制的装有 BaF_2探头的高探测效率的正电子湮没寿命谱仪测量了在室温下正电子素 o-Ps 与 p-RPhG 及 m-RPhG(R=NO_2,Cl,H,CH_3,cH_3O)在20%(V/V)二氧六环水溶液中的络合形成速度常数。实验结果表明,这些o-Ps-M 络合形成速度常数 K 值均与作为配位体的 p-RPhG、m-RPhG 的碱性解离常数 K 的负对数 pK_2 呈线性函数。这表明上述瞬态络合反应满足线性自由能关系,由此可推断出上述络合反应的一些重要性质。     

高燃速丁羟推进剂配方研究

通过多种途径的试验,对高燃速丁羟推进剂配方进行了研究.试验结果表明,采用超细防结块氧化剂和液固组合燃速催化剂能使推进剂的燃速达到70mm/s以上(在6.864Mpa压强下);采用组合工艺助剂可改善推进剂工艺性能.本推进剂燃烧稳定,压强指数和温度敏感系数较低,力学性能良好,为高燃速推进剂的研制奠定了良好的基础.     

复杂系统的可靠性分析方法研究

本文对未来的运载器的复杂控制系统的可靠性建模、分配和预计的一般方法和程序及综合分析方法进行了讨论和研究。并简述了复杂系统的计算机辅助可靠性分析。     

X射线探伤机空气比释动能率测量不确定度评定

基于X射线探伤机空气比释动能率测量的数学模型，对其测量不确定度进行了评定。     

门限自回归模型参数的局部正交设计寻优法

在采用点值图确定门限区间个数的基础上，对门自回归模型中门限值、滞后步长、各门限区间模型阶数，利用正交设计方法寻优，计算工作量锐减，却可得到精度较高的预报模型。